The influence of mining factors on seismic activity during longwall mining of a coal seam

In this article an attempt to determine the influence of mining factors on the seismic activity during the longwall mining of the upper layer of coal seam no. 405/2 in one of the Polish hard coal mines in the Upper Silesian Coal Basin was conducted. Two longwall panels were mined in analogous geological conditions and based on the same mining system and technology. However, there was significant difference with regards to the mining factors, which was reflected in the observed seismic activity. Some tools used in mining seismology were applied to illustrate the aforementioned influence of mining factors, e.g. the frequency-energy distribution, the frequency-magnitude distribution, the 2 D distribution of released seismic energy, the relationship between released seismic energy and the volume of mined coal, the Benioff strain release, and the Gutenberg-Richter(GR) b coefficient distribution(b is the proportion between high and low energy tremors). Concerning the Benioff strain release, a new solution, based on the slope of a fitted line in a moving time window, is proposed.     

煤泥燃烧过程中汞的迁移行为研究

采用在线汞测试方法，以山西省低热值煤电厂中掺烧的煤泥为研究对象，利用实验室小型流化床，研究煤泥中汞的热转化行为差异及共性特征、影响煤泥热转化过程中汞迁移的关键因素，以揭示煤泥热转化过程中汞污染物的迁移机理。结果表明，同一种煤泥，相同气氛，800、900、1 000 ℃下，燃烧温度对煤泥中的汞的释放比例没有变化；相同温度，汞的释放比例为氮气>空气>氧气。3种煤泥在相同燃烧条件下，汞的释放特征相似，元素汞的释放量和释放比例差异较大。释放量与煤泥中的汞含量正相关，释放比例与煤泥中汞的赋存形态有一定关系。     

Physiochemical structure of semicoke derived from co-carbonization of coal and sawdust blends

The substitution of coal blending with sawdust had been widely investigated for metallurgical coke production. In this paper, the physiochemical structures of the semicoke derived from sawdust/coals blends co-coking were characterized by several analytical techniques including FTIR-ATR, XPS, NMR, OM, and SEM. Meanwhile, the influence of the sawdust on the physicochemical properties of the sawdust/coals blends were also investigated. Results indicated that partial substitution of coal blending with sawdust benefited from the formation of colloid and optical anisotropy due to the positive synergetic effect, whereas high proportion of sawdust (>10 wt%) inhibited the agglomeration of semi-coke. On the other hand, the semicoke consisted primarily of aromatic carbons replaced by the oxygen linked to carbons and aliphatic carbons when the coal blending was replaced by high proportion of sawdust, causing a less polyaromatic graphite-like structure formation in the semicoke.     

煤基高能量密度燃料的合成及表征

高能量密度燃料是为新型高性能飞行器提供动力保障的关键,其合成及应用研究具有重要的前瞻性和重大战略意义。煤炭是我国的主体能源和重要原料,通过煤直接转化获取的煤基油,充分保留了煤中特有的环状分子化学结构,具有良好的热安定性和较高的能量密度,被认为是高超音速飞行器的优选燃料。以煤直接液化工艺生产的煤液化石脑油馏分为起始原料,通过富集轻质芳烃、化学合成、催化加氢稳定和产物分离提纯等方法制备煤基高能量密度燃料,并对其产物进行分子结构表征和性能评价。结果表明,煤直接液化生产的石脑油馏分是一种优异的催化重整原料,经催化重整富集轻质芳烃后,其轻质芳烃质量分数高达71.05%。Diels-Alder化学合成主产物是由多个封闭环平面组成且具有空间立体构型的二环或三环烃类物质,质量分数为46.18%,因分子内存在较大的张力能,结构紧凑,其拥有更大的密度和体积热值。煤基高能量密度燃料的密度和体积热值分别为0.8990 g/cm3与38.06 MJ/L,均大大超过现行的国内石油基喷气燃料(RP-3和RP-6)、煤基大比重喷气燃料、美国和俄罗斯军用标准。与单一纯物质合成高能量密度燃料(JP-10和T-10)比较,其密度与体积热值偏小。究其原因主要是轻质芳烃的富集度仅为71.05%,需进一步提高其轻质芳烃质量分数。另外,制备的煤基高能量密度燃料种类复杂,其主产物质量分数仅46.18%,下一步可重点调控合成产物的分子构型和纯化分离。     

Reviews of clean coal conversion technology in China:Situations & challenges

It is important to develop the advanced coal to chemicals industry (ACCI) against a backdrop of coal-based energy structures,excessive imported oil and natural gas,and strict environmental con-straints in China.In this study,the technology and industry of China's ACCI are reviewed to explain the effect of using coal to replace oil and natural gas,and the corresponding resource and environmental burdens that this will create.Development trends in technology and industry are also proposed to explore future scenarios.The review shows that although excellent progress has been made on an indus-trial scale,demonstrative level,and in terms of technology and equipment,the lack of strategic under-standing,severe external constraints,partly underdeveloped technologies,and weak foundations must be immediately addressed.Therefore,it is necessary to clarify the importance that the ACCI has on the energy revolution and energy system.Based on technological innovation,a variety of external factors should be considered as a whole with emphasis on filling the knowledge gap of theoretical foundations and industry standards to support high-quality development for ACCI.     

烧结时间对含铅玻璃制备微晶玻璃析晶及性能的影响

以铅玻璃与粉煤灰为原料，通过协同熔炼制备了微晶玻璃。通过XRD和SEM等手段研究了不同烧结时间下微晶玻璃的物相组成及显微结构，测定了微晶玻璃的密度、吸水率、维氏硬度和化学抗性。结果表明: 延长烧结时间对含铅玻璃加入量为40%(FG40)、50%(FG50)样品的晶相类型和晶化程度有影响，而对含铅玻璃加入量为60%(FG60)、70%(FG70)和80%(FG80)样品的影响较小。随着烧结时间延长，样品晶化程度提高，晶体长大，玻璃相减少。适宜的含铅玻璃加入量为50%~70%，对应的FG50、FG60、FG70样品最佳烧结时间分别为4 h、3 h、3 h。     

Intrinsic Defect Limit to the Growth of Orthorhombic HfO2 and (Hf,Zr)O2 with Strong Ferroelectricity: First-Principles Insights

It is believed that promoting the fraction of ferroelectric orthorhombic phase (o-phase) through O-poor growth conditions can increase the spontaneous polarization of HfO₂ and (Hf,Zr)O₂ thin films. However, the first-principles calculations show that the growth may be limited by the easy formation of point defects in the orthorhombic and tetragonal phases of HfO₂, ZrO₂, and (Hf,Zr)O₂. Their dominant defects, O interstitial (O_i) under O-rich conditions and O vacancy (V_O) under O-poor condition, have low formation energies and quite high density (10¹⁶–10¹⁹ cm⁻³ for 800–1400 K growth temperature). Especially, O_i has negative formation energy in tetragonal HfO₂ under O-rich condition, causing non-stoichiometry and limiting the crystalline-seed formation during o-phase growth. High-density defects can cause disordering of dipole moments and increase leakage current, both diminishing the polarization. These results explain the experimental puzzle that the measured polarization is much lower than the ideal value even in O-poor thin films and highlight that controlling defects is as important as promoting the o-phase fraction for enhancing ferroelectricity. The O-intermediate condition (average of O-rich and O-poor conditions) and low growth temperature are proposed for fabricating HfO₂ and (Hf,Zr)O₂ with fewer defects, lower leakage current, and stronger ferroelectricity, which challenges the belief that O-poor condition is optimal.     

煤矿冲击地压与冒顶复合灾害研究

随着煤矿向深部发展,矿井动力灾害既表现出冲击地压的部分特征,又表现出冒顶的部分特征。2种典型的灾害打破以往冒顶与冲击地压的发生具有一种互为逆向性的认知规律,在深部高应力煤巷,特别是留顶煤巷道中出现了相互诱导、复合发生的新灾害类型。在总结山东、山西和新疆矿区典型巷道冲击致顶板(顶煤)动力灾害特征的基础上,提出了深部巷道冲击地压与冒顶复合灾害的概念、机理与分类,指出复合灾害机理关键点在于揭示巷道整体系统和破碎区子系统的稳定原理及其2者间的相互影响。建立了巷道发生复合灾害的力学模型,根据扰动响应失稳判据,提出并得到了巷道发生复合灾害的临界应力Pcr、临界软化区半径ρ_cr和最大容许采扰应力增量σ_max,厘清了灾害发生的主控因素,分析了煤岩冲击倾向指数K、支护强度ps、巷道半径ρ₀、煤岩强度σ_c等对灾害发生的影响规律,同时阐明了围岩塑性软化、破碎深度随地应力增加的发育规律。研究结果表明,破碎发育巷道的动力失稳主体为弹性区、软化区与破碎区构成的不稳定系统,垮落主体为破碎区;稳定的破碎区提升了巷道冲击启动临界值,使其启动难度增大,但破碎区的发育又易引起顶煤垮落;巷道稳定支护是解决复合灾害的关键,科学合理支护既能有效调控围岩破碎防冒,又能提升冲击启动临界值。通过理论研究,揭示了巷道冲击地压与冒顶复合灾害的发生机理,阐明了巷道软化与破碎区及其稳控支护对深部破碎发育巷道动力灾害防治的重要性。     

Review on development of metal/ceramic interpenetrating phase composites and critical analysis of their properties

Metal/ceramic composites are in high demand in several industries because of their superior thermo-mechanical properties. Among various composite types, the interpenetrating phase composites (IPCs) with percolating metallic and ceramic phases offer manifold benefits, such as a good combination of strength, toughness, and stiffness, very good thermal properties, excellent wear resistance, as well as the flexibility of microstructure and processing route selection, etc. The fabrication of metal/ceramic IPCs typically involves two steps - i) processing of an open porous ceramic body, and ii) infiltration of metallic melt in the pores to fabricate the IPC. Although significant progress has been made in recent years for developing both porous ceramics and melt infiltration methods, to the best of the knowledge of the authors, no review article summarizing all the aspects of processing and properties of IPCs has been published till date. This review article is aimed at filling this gap. Starting with a brief introduction about the current status and applications of IPCs, the various processing routes for fabricating open porous ceramic preforms and melt infiltration techniques have been discussed. Subsequently, the data available for various important physical, mechanical, and thermal properties for IPCs have been critically analyzed to thoroughly understand their dependence on various structural and processing parameters. To compare the properties of IPCs with other relevant materials, seven different Ashby material property maps have been used, and the domains for IPCs have been created in them. For each map, the concept of material indices has been employed to critically discuss how IPCs perform in relation to other material classes for various optimum design conditions. Finally, a detailed future outlook for further research on IPCs has been provided.